**** Make sure you find your BONT SIZE here
**** Please contact us at email@example.com for size availabilty****
Introducing the new Bont BNT Short Track boot
The BNT short track boot is a step up from the Z. Unlike the Z which is constructed with carbon and fiberglass, the BNT is made with 100% carbon which makes it stiffer than the Z.
The outer skin is also made of a higher-grade material than the Z. The foam padding is thinner and harder than the Z and there is no thermoplastic in the boot which makes it a little less heat moldable but lighter in weight. The boot is still heat-moldable from the resin.
The BNT has set a new benchmark in the inline skating world and we hope it will do the same in short track. Top inline skaters have said that it is the best-fitting stock boot they have ever worn. We also have a BOA edition which adds a BOA dial for getting your skates in quick. The BNT is one of the lightest boots that we have ever made, so light you will hardly know you have it on.
- Base: 100% carbon with matte finish
- Outer skin: Durolite
- Liner: Suede-L
- Innersole: EVA thermo-moldable
- Heat moldable: Fully heat moldable base utilizing epoxy thermoset resin
- Padding: Neoprene 2mm
- Protection: none
- Vegan: Yes
The legendary Bont short track Platinum K390 ice speed skating blade is back. Made with Böhler K390 powder metal tool steel which is slow ground to produce a perfectly straight piece of steel. The powder metal structure is very fine which gives exceptional gliding properties. Able to hold its edge up to 8 times longer than normal steel blades the tube has the highest bend retention of any blade on the market.Specifications
- Cup material: Aluminum 7075 T6
- Radius: 9m
- Length: 15", 15.5", 16", 16.5", 17", 17.5", 18"
- Blade thickness: 1.1mm
- Hardness: 64 Rockwell
- Bend: Machine bent
- Cup height: 25mm(Standard)
The Bont Platinum K390 is regarded by many short track skaters as the best short track blade ever made. In the old days, national team skaters would contact short track blade manufactures and go through a lot of blades checking to find which ones were straight and the leftovers were sold to shops to onsell to the skaters. We didn't think that is a fair system and we wanted everyone to have access to the best blades all the time. With the Bont Platinum short track blade, every blade is good so no one needs to check to find the best blade in a batch.
Here are the steps we took to create the fastest short track blade:
- Normally, when you buy blade steel, it comes on a roll. When the blade is made, we take the steel and insert it into the slot in the same direction the steel is curved on the roll. But, it is not ideal because it has way too much curve and it is wavy. For the Platinum short track blade, we paid an additional cost to receive flat sheets of steel rather than buy it on the roll. The steel is flat to start with even before we grind it. Even after grinding, rolled still will still have a memory of being bent.
- We buy the steel that is 1.3mm thick and then cut it to shape and then it gets attached to a plate where the grinding stone grinds 0.1mm off it, it is flipped and 0.1mm is ground off the other side. It does not sound like much, but with such hard steel, it takes quite some time to grind it perfectly flat. It is common in short track blade manufacturing to put 10 blades on the plate and grind them down quickly using cheap stones to save costs. When you grind the steel quickly it heats the metal and causes it to warp. Machining time is expensive so this cuts costs. For the Bont Platinum short track blade, we imported special high-end grinding stones from Germany, and we slow grind just two blades at a time. We pay a number of additional costs for this project to create the same high-end blade for all skaters. If it is not already clear, our mandate for this blade is to create the best blade at any cost. There should not be good and bad blades, only the best short track blades.
- The slot that holds the blade has a gap on each side to give room for the glue. This gap leaves room for the blade to warp. We tested many types of glue to find one that bonds better than on previous blades and when we found a new improved glue we were able to reduce the size of the slot by 0.1mm. This doesn't sound like much but it means less warping as there is less gap for the steel to warp.
- While the glue sets, there is a chance that the blade can warp. The glue we use takes many hours to dry. Depending on the length of the blade, we hold the whole blade at a minimum of nine different points to perfectly maintain the blades bend while it sets for 14 hours. These jigs are incredibly expensive and we have a number of them to complete a production run.
- We did a 'brilliance polish' on the side of the blade so when you lean over and the side of the blade is touching the ice, there is as little friction as possible.
- For the tube stiffness, we worked with a number of the world's best national teams. If the tube is too stiff it can cause skaters to crash. If it is too flexible, it will absorb the skater's power. We used CAD-CAM software mixed with real-life testing to find the optimal tube stiffness.
- The tube is made of 7075 T6 aluminum which is why the Bont Platinum is a silver color as it is very difficult to anodize 7075 aluminum.
The result of all this work is the best and fastest short track blade ever produced. We are sure you will appreciate the effort that we put into this blade to allow you to perform at your best.
LIGHTER. STRONGER. FASTER.
We push the limits of technology to help you perform at your best.